Internet Of Things

contoller / Smart Hub

The controller runs the bridge devices that each individual vendor brings with their devices. It's a single central place to run all of the devices from.

The absolute Ferrari on controllers is:

HomeSeer HomeTroller S6: $899

So we go for the Smartthings hub which supports Wifi, Zigbee, Z-Wave at $99

This is the list of compatible devices

As an alternative you can run open source software, which will run on a raspberry pi with a zigbee usb controller.

Project Things from Mozilla

list of compatible devices

ppenHAB written in java

Home Assistant written in python

Protocols

You would think that this would be straightforward but it isn't. Common protocols are:

- Wifi

- Zigbee

-- LightLink (EU)

-- Home Automation (US) Note - these two protocols don't play well with each other. It looks like HA is being phased out in favour of LL.

- Z-Wave

- X-Wave

Smart Lighting

Bridges

The HUE bridge has a limit of 50 connections. You can add another bridge to your HUE app, but you will have to switch bridges within the app, which is annoying. You also can't backup your setup.

The Dresden Elektronik Raspbee Premium (SD card image [1]) doesn't have the 50 device limitation and has a backup function. It can be used through the HUE app itself. It also uses deConz software to detect devices.

Turning transforming dumb switches

Busch Jaeger has three switches (rocker, LED dimmer) which will integrate with the HUE bridge. Once you put in a wall insert, you can put different controllers on top of it (one, two or four lane) to control the dumb light. You can then add extra remote control light switches in other location to control the same lights.

File:busch-jaeger-zigbee-light-link.pdf Read the systems manual here

[2] has the best prices for the dimmers I have found so far.

Philips HUE

It's worth getting a Philips Hue starter Pack with the 2.0 bridge to start you off. NB Philips Hue Lux (only white dimmers) controllers can't control LED lamps with colours, but the full HUE kit can control the white LUX lamps

compatible devices

iconnect hue supported devices list

Integrating dumb lights in my smart home

Busch Jaeger will integrate with the HUE bridge

Apparently Friends of Hue will launch a large range of dumb light switches but probably only for Hue bulbs Hue Home Lighting. The partners will be Busch-Jaeger, Feller, Illumra, Niko and Vimar.

Hue also has a motion sensor to trigger the lights. No good for outdoor use. It's very easy to set up but only compatible with Hue lights and won't work with homekit stuff. They are also temperature sensors which you can see in smarthings.

Tips and tricks

When you add lights to a scene, delete the alarm which contains the scene and set it up again. Otherwise not all the lights will always turn on when the alarm goes off.

Use the HUE 1 app for most things, but use the HUE 2 app for the light switches / dimmers. It has more options

The HUE 1 app has support for the Random setting in the alarnms, allowing lights to turn on / off +- up to 30 minutes from the set time. For some reason, Hue2 doesn't have this

Innr

They also have a large selection of products advertised to connect with the Osram or Hue brigdes (including a GU10 for EUR 20) shop here

Osram

Osram Lightify lights should work very well with the Hue system, as they are both Zigbee. However, both Philips as Osram are being a bit silly in their implementation of the Zigbee protocol, which leads to some strange workarounds.

Currently the GU10 lights are unstable due to Philips Hue updates, which means that all my connected lights won't turn off fully using the Hue controller, after I added 1 new GU10 light.

The plugs work well too, but it could be that they need resetting or touchlink connections before they work. They didn't need an update from the lightify gateway for me. Detect them as a light with the switch set to on (light is green) and they will turn up as an on/off switch.

resetting

turn the light or plug off for 3 seconds, turn it on for 3 seconds, repeat 5 times. Leave on and wait (10s). If the light blinks, it has worked, if not, repeat.

connecting to Hue

1. First you need to upgrade the firmware. If you don't do this, the lights will not go all the way off. This can only be done through the Osram Lightify Gateway (see below).
2. After the update, unplug the Osram Lightify Gateway entirely, otherwise it will pick up the lights after the reset
3. reset the light (see above)
4. turn light OFF
5. start up Hue app
6. start searching for lights in Hue app
7. turn light ON

Note: if the light is already on, the Hue app won't find the light for some reason

1. profit

Using touchlink

1. Download the lamp finder jar or File:LampFinder.jar
2. Plug the lamp / plug close to the Hue bridge (< 30cm away)
3. start the jar
4. press the button on the Hue bridge to connect
5. search for the lamp.

Alternatively

You can do light stealing from the Hue local API. In a web browser go to

http://x.x.x.x/debug/clip.html

where x.x.x.x is your IP address of the hub. This should bring up a web page. Put the light you want to steal within 30cm’s of the hub

You need to URL and/or message body

Register a user
URL: /api
Message Body: {“devicetype”: “HueLights#API”}
Press the Post Button

This will give you a long user name in the response box

URL: /api/YOUR_USERNAME/config
example: /api/7773d8bf606360d23d968ff165e77293/config
Message Body: {"touchlink":true}
Press the Put button

URL: /api/YOUR_USERNAME/lights
Clear the Message Body
Press the Post Button

On my setup this caused the living colours light to flash, I then immediately ran the Connect New lights in the Hue App. Sure enough the Bloom light showed up in the app.

Hope that helps someone else in the future

From here

upgrading Osram Firmware

1. reset the light
2. plug in the Lightify gateway
3. start up the Lightify app
4. plug in light at as close a distance as possible to the gateway
5. detect the light using the app (you may have to restart the app, as it doesn't always show that it's detected the light properly)
6. use the app to update the lights -> you will have to press update a few times before it goes. Once it does go it can take a LONG time. Just wait for the blue line.

troubles with upgrading

The remaining issues I found out to be defective bulbs where they were not updating to the latest Lightify firmware(They are stuck on v1.03.07 and should be on v1.04.12)

My lights are stuck on firmware 1.03.07 according to the Hue app, but the lightify app (connected to a Lightify Gateway) says they are updated to 1.04.12 and can't be updated

Sent back to customer service and replaced.

Bulb types

E27 = screw bulb

GU10 = the little spots with 2 plugs

E27

For lighting you can use many things but the cheapest are:

Cree connected bulb $14.97

GE Link connected LED $14.97

Philips hue white / amazon GBP 14,99

Philips hue white / BOL EUR 19,95 + EUR 1.99 verzending = EUR 21.95

Lampenonline hue lux white e27 EUR 17.96 + EUR 5.95 postage = EUR 23.91

GU10

The Philips one is ridiculously expensive.

Innr / EUR 20 don't know if it works

Osram Lightify GU10 / Conrad EUR 29.99 + EUR 4.95 postage = EUR 34.94 Very iffy support with Hue (I currently can't turn them off)

or

8x GU10 to E27 converter plugs for $7.29

== Display

heating

For heating you need a smart radiator valve / TRV (thermostatic radiator valve) / Central heating valve

Conrad has these which are programmable but not smartthings

Honeywell Evohome will be compatible with smartthings soon (they have been saying for years)

Tado

Danfoss doesn't seem to work

MiHome has a hack

So far it looks like you will have to connect the brand thermostat to the TRV

Your smart heating package constists of the following:

- TRVs for the radiators

- a thermostat

- a controller / receiver for the CV installation.

The controller / receiver comes in 2 types:

- opentherm: an open standard that allows graduated control over the heat the CV generates http://centrale-verwarming-combiketels.welke-kiezen-kopen.nl/opentherm-wat-is-het-voordeel-cv-ketels.php

- on / off

When you install your system, you also need a bypass to allow for water to circulate. A possibility is to have one of your radiators on all the time, to act like a bypass.

Honeywell has a 4 zone wifi kit for EUR 483 https://www.cvkoopjes.nl/honeywell-zoneregeling/honeywell-evohome-wi-fi-4-zone-aanuit-pakket.html?gclid=CLPV8bz8nswCFegp0wodKVgGSA#/75-garantie-2_jaar_standaard/ and for EUR 505 http://www.paradigit.nl/honeywell-evohome-multi-zone-radiatorpakket-on-off/80039504/details.aspx?channel_code=210&s2m_product_id=80039504&utm_source=adcore-v4&gclid=CMbUnKz7nswCFeQp0wodjBIC6Q

You can buy the receiver seperately for around EUR 100,-

https://www.google.nl/search?q=Honeywell+opentherm+ontvanger&ie=utf-8&oe=utf-8&gws_rd=cr&ei=hnkYV7HnIcSRgAbtnIOgAg#q=Honeywell+opentherm+ontvanger&safe=off&tbm=shop

There's also a remote sensing TRV head, for if your radiator is enclosed

http://www.honeywelluk.com/products/Valves/Thermostatic-Radiator-Valve/TRV-Accessories-Head/Remote-Sensing-TRV-Head/

https://www.kijkvoelbeleef.nl/Honeywell/Producten/Product/Distance-Plus/ (in NL they are called Distance Plus)

for around EUR 25 https://www.installatievakwinkel.nl/honeywell-radiatorthermostaatknop-recht-economy-distance-wit-t900120w0?utm_source=beslistslimmershoppen&channable=e5791.MzA1MjAwMzY5Mjc&utm_content=Honeywell&utm_campaign=beslist&utm_medium=cpc&utm_term=30520036927

or EUR 59 https://www.installatievakwinkel.nl/honeywell-radiatorthermostaatknop-recht-distance-plus-wit-t950120w0

but I don't know if they are compatible with EvoHome.

Unfortunately the Nefit Ecomline HR line of CVs is on/off only and doesn't have an opentherm adapter. There is an adapter for their own smart thermostat, but you can't use that to connec to the Honeywell Evohome.

Motion detection

Outdoor the best way seems to be to connect a Fibaro Relay to a standard "dumb" outdoor motion detector Controlling Lights with Fibaro Relays

The way Alwas in this post did

Power Plugs

Philips used to make a Living Whites powerplug which was dimmable with Hue, but it seems to be discontinued.

Wemo has a smart plug (but Wifi, not Zigbee)

Osram has a lightify plug but it only supports on and off. EUR 25,- at Azerty

Innr has smart plug no idea if it supports dimming. EUR 35,-

other devices

Smart Home DB a database with loads of devices linked to reviews and howtos

fakeTV - programmable but not zigbee

TV Simulators tend to have a few options: an mp3 player, a timer, an automatic mode where they turn on when it gets dark and then goes for a few hours (typically 4 or 8 hours) before turning off. You can't get them on Zigbee, so I guess you have to get a zigbee enabled power plug.

TV Simulators on Amazon

AGPtEK simulator

Mabor

Eposgear

fake Dog

Fibaro 4 in one motion sensor GBP 45,61

Wulian for curtain controllers, door locks, luxaflex, sensors, light bulbs, doorbells CHINA

How it works

[http://www.makeuseof.com/tag/control-philips-hue-lights-arduino-and-motion-sensor/ an explanation of Philips, how to control them using an Arduino and what Zigbee is (basically a mesh)